FSM050NPT
应用霍尔效应开环原理的电流传感器,能在电隔离条件下测量直流,交流,脉冲以及各种不规则波形的电流.
Open loop current sensor based on the principle of Hall-effect It can be used for measuring AC,DC, pulsed and mixed current.
|
电参数/Electrical characteristics |
||||||
|
型号 Tpye |
FSM006NPT |
FSM015NPT |
FSM025NPT |
FSM050NPT |
||
|
IPN |
原边额定输入电流 Primary nominal input current |
6 |
15 |
25 |
50 |
A |
|
IP |
原边电流测量范围 Measuring range of primary current |
0～±19.2 |
0～±48 |
0～±84 |
0～±150 |
A |
|
RM |
取样电阻 Sampling resistance |
100±0.5% |
50±0.5% |
50±0.5% |
25±0.5% |
Ω |
|
VSN |
副边额定输出电压 Nominal output voltage |
0.625±0.5% |
0.625±0.5% |
0.625±0.5% |
0.625±0.5% |
V |
|
KN |
匝数比 Turns ratio |
1:960 |
1:1200 |
1:2000 |
1:2000 |
|
|
Vc |
电源电压 Supply voltage |
+5(±5%) |
V |
|||
|
Ic |
静态功耗 Staticpower consumption |
IP=0 <10 |
mA |
|||
|
Vd |
绝缘电压 Insulation voltage |
在原边与副边电路之间3KV有效值/50Hz/1分钟 3KV RMS /50Hz/1 min between primary and secondary side circuits |
||||
|
εL |
线性度 Linearity |
<0.1 |
%FS |
|||
|
X |
精度 precision |
TA=25℃ ±0.5 |
% |
|||
|
VO |
零点失调电压 Offset voltage |
IPN=0 TA=25℃ 20±1% |
mV |
|||
|
VOT |
失调电压温漂 Thermal drift of V0 |
IP=0 TA=-25～+85℃ <±0.5 |
mV/℃ |
|||
|
TR |
响应时间 Response time |
<1 |
μs |
|||
|
di/dt |
跟随精度 Following accuracy |
>50 |
A/μs |
|||
|
f |
频带宽度(-1dB) Frequency Bandwidth (-3dB) |
DC～200 |
kHz |
|||
|
TA |
工作环境温度 Ambient operating temperature |
-40～+85 |
℃ |
|||
|
TS |
贮存环境温度 Ambient storage temperature |
-40～+125 |
℃ |
|||
|
标准 Standard |
GI/FS0105 |
|||||
外形尺寸(mm)/Dimensions of drawing(mm)
|
初级线匝 Primary turn |
初级额定电流(A) Primary rated current (A) |
输出电压(V) Output voltage (V) |
初级阻值 (mQ) Primary resistance (mQ) |
初级电感 (μH) Primary inductance (μH) |
输入PIN连接 Enter PIN connection |
|
1 |
±6(±15,±25,±50) |
2.5±0.625 |
0.18 |
0.013 |
|
|
2 |
±3(±7.5,±12.5,±25) |
2.5±0.625 |
0.81 |
0.05 |
|
|
3 |
±2(±5,±8.3,±16.6) |
2.5±0.625 |
1.62 |
0.12 |
|
Input current(A)
该产品有两种接入方式The product has two access methods
电缆线穿孔输入 Cable punch input
2-PCB 输入方式 PCB input mode
可以根据需要来选择适合的电流输入方式The suitable current input mode can be selected according to the needs
1,对于电缆线电流输入方式,电缆线要穿过霍尔电流传感器的孔;以 FSM006NPT为例,如果 电缆线穿孔是1匝时,额定电流是6A, 如果电缆线穿孔绕2匝或者3匝时,额定的电流就 为 3A或者是2A;如果按照此种输入方式进行时,请不要同时使用PCB输入方式;
For the cable current input mode, the cable should pass through the hole of the Hall current sensor; Taking FSM006NPT as an example, if the cable perforation is 1 turn, the rated current is 6A, if the cable perforation is 2 or 3 turns, the rated current is 3A or 2A; If this type of input is used, do not use PCB input at the same time;
2,对于PCB输入方式,根据输入PIN的连接方式来判定输入的匝数与额定的输入电流参数.输入PIN 的连接方式有三种：分别是1T,2T,3T;对应的输入额定电流为：6A,3A,2A; 使用此方式时不要同时使用穿孔输入方式;
For PCB input, the number of turns and rated input current parameters are determined according to the connection mode of the input PIN. There are three ways to enter the PIN: 1T,2T,3T; The corresponding input rated current is: 6A,3A,2A; When using this method, do not use the punch input method at the same time;
Hot Tags: fsm050npt, China fsm050npt manufacturers, suppliers, factory, Plastic Indicator, Punching Machine Safety Light Curtain, Ultra thin Safety Light Curtain, Keli AMI, OIML S Beam Load Cell, Split Core Current Sensor SZ140KBD12
You Might Also Like
Send Inquiry