
FSM025ES5
应用霍尔效应原理开发的电流传感器,能在电隔离条件下测量直流,交流,脉冲以及各种不规则波形的电流.有极性无负值的一款单电源工作模式的霍尔电流传感器.
The current sensor developed by Hall effect principle can measure DC, AC, pulse and various irregular wave forms of current under the condition of electrical isolation. A Hall current sensor with polarity and no negative values in single power mode.
|
电参数/Electrical characteristics |
||||||
|
型号 Type |
FSM010ES5 |
FSM025ES5 |
FSM050ES5 |
FSM075ES5 |
||
|
IPN |
原边额定输入电流 Rated input current on primary side |
10 |
25 |
50 |
75 |
A |
|
IP |
原边电流测量范围 Primary current measurement range |
0~20 |
0~50 |
0~100 |
0~150 |
A |
|
RM |
取样电阻 Sampling resistance |
50±0.1% |
50±0.1% |
25±0.1% |
16.5±0.1% |
Ω |
|
VSN |
副边额定输出电压 Rated output voltage of secondary side |
0.625±0.5% |
0.625±0.5% |
0.625±0.5% |
0.625±0.5% |
V |
|
KN |
匝数比 Turns ratio |
800±2 |
2000±2 |
2000±2 |
2000±2 |
|
|
Vc |
电源电压 Supply voltage |
+5(±5%) |
V |
|||
|
Vd |
绝缘电压 Insulation voltage |
在原边与副边电路之间3KV有效值/50Hz/1分钟 |
||||
|
εv |
精度 Precision |
<±0.2 |
%FS |
|||
|
εL |
线性度 linearity |
<0.1 |
%FS |
|||
|
V₀ |
零点偏移电压 Zero offset voltage |
Ip=0 TA=25℃ 2.5±0.5% |
V |
|||
|
VOT |
失调电压温漂 Offset voltage temperature drift |
Ip=0 TA=-25~+85℃ <±0.5 |
mV/℃ |
|||
|
TR |
响应时间 Response time |
<1 |
us |
|||
|
di/dt |
跟随精度 Following accuracy |
>100 |
A/us |
|||
|
f |
频带宽度(-1dB) Band width (-1dB) |
DC~200 |
kHz |
|||
|
TA |
工作环境温度 Operating ambient temperature |
-40~+85 |
℃ |
|||
|
TS |
贮存环境温度 Storage ambient temperature |
-40~+125 |
℃ |
|||
|
标准 Standard |
GI/FS0105 |
|||||
外形尺寸(mm)/Dimensions of drawing(mm)

输入输出特性/Input-output characteristic:
下面是FSM025ES5的输入输出的关系曲线
The following is the relationship between the input and output of the FSM025ES5
|
输入电流(A) Input current |
-80 |
-75 |
-50 |
-25 |
0 |
25 |
50 |
75 |
80 |
|
输出电压(V) Output voltage |
0.500 |
0.625 |
1.250 |
1.875 |
2.500 |
3.125 |
3.750 |
4.375 |
4.500 |

使用说明/Instructions
错误的接线可能导致传感器损坏,请按照标定的正确电流方向进行安装测试.
Incorrect wiring may cause damage to the sensor. Install the sensor according to the correct current direction.
初级的导体完全充满初级孔径时动态表现(di/dt和相应时间)为最佳效果;
The primary conductor performs best dynamically (di/dt and corresponding time) when fully filled with the primary aperture
初级导体的温度不应超过100℃.
The temperature of the primary conductor should not exceed 100℃.
可根据客户的要求定制产品.
Products can be made according to customers' requirements.
Hot Tags: fsm025es5, China fsm025es5 manufacturers, suppliers, factory, Plastic Indicator, Bending Beam Type Weighing Module, Detection and Measurement Light Curtain, OIML S Beam Load Cell, Remote Display DPM, EV Current Sensor SP31MD12
Previous
FSM025LPTNext
FSM006PT3.3You Might Also Like
Send Inquiry











